With a market demand for low cost, easy to produce, flexible and portable applications in healthcare, energy, biomedical or electronics markets, large research programs are initiated to develop new technologies to provide this demand with new innovative ideas. One of these fast developing technologies is organic printed electronics. As the term printed electronics implies, functional materials are printed via, e.g. inkjet, flexo or gravure printing techniques, on to a substrate material. Applications are, among others, organic light emitting diodes (OLED), sensors and Lab-on-a-chip devices. For all these applications, in some way, the interaction of fluids with the substrate is of great importance. The most used substrate materials for these low-cost devices are (coated) paper or plastic. Plastic substrates have a relatively low surface energy which frequently leads to poor wetting and/or poor adhesion of the fluids on the substrates during printing and/ or post-processing. Plasma technology has had a long history in treating materials in order to improve wetting or promote adhesion. The µPlasma patterning tool described in this thesis combines a digital inkjet printing platform with an atmospheric dielectric barrier discharge plasma tool. Thus enabling selective and local plasma treatment, at atmospheric pressure, of substrates without the use of any masking materials. In this thesis, we show that dependent on the gas composition the substrate surface can either be functionalized, thus increasing its surface energy, or material can be deposited on the surface, lowering its surface energy. Through XPS and ATR-FTIR analysis of the treated (polymer) substrate surfaces, chemical modification of the surface structure was confirmed. The chemical modification and wetting properties of the treated substrates remained present for at least one month after storage. Localized changes in wettability through µPlasma patterning were obtained with a resolution of 300µm. Next to the control of wettability of an ink on a substrate in printed electronics is the interaction of ink droplets with themselves of importance. In printing applications, coalescence of droplets is standard practice as consecutive droplets are printed onto, or close to each other. Understanding the behaviour of these droplets upon coalescence is therefore important, especially when the ink droplets are of different composition and/or volume. For droplets of equal volume, it was found that dye transport across the coalescence bridge could be fully described by diffusion only. This is as expected, as due to the droplet symmetry on either side of the bridge, the convective flows towards the bridge are of equal size but opposite in direction. For droplets of unequal volume, the symmetry across the bridge is no longer present. Experimental analysis of these merging droplets show that in the early stages of coalescence a convective flow from the small to large droplet is present. Also, a smaller convective flow of shorter duration from the large into the small droplet was identified. The origin of this flow might be due to the presence of vortices along the interface of the bridge, due to the strong transverse flow to open the bridge. To conclude, three potential applications were showcased. In the first application we used µPlasma patterning to create hydrophilic patterns on hydrophobic dodecyl-trichlorosilane (DTS) covered glass. Capillaries for a Lab-on-a-chip device were successfully created by placing two µPlasma patterned glass slides on top of each other separated by scotch tape. In the second application we showcased the production of a RFID tag via inkjet printing. Functional RFID-tags on paper were created via inkjet printing of silver nanoparticle ink connected to an integrated circuit. The optimal operating frequency of the produced tags is in the range of 860-865 MHz, making them usable for the European market, although the small working range of 1 m needs further improvement. Lastly, we showed the production of a chemresistor based gas sensor. In house synthesised polyemeraldine salt (PANi) was coated by hand on top of inkjet printed silver electrodes. The sensor proved to be equally sensitive to ethanol and water vapour, reducing its selectivity in detecting changes in gas composition.
Muscle fiber-type specific expression of UCP3-protein is reported here for the firts time, using immunofluorescence microscopy
An analysis was made of the various possible activators of single-chain urokinase-type plasminogen activator (scu-PA) in the dextran sulphate euglobulin fraction (DEF) of human plasma. scu-PA activators were detected in an assay system in which the substrate scu-PA, in physiological concentration (50 pM), was immuno-immobilized. After activation of the immobilized scu-PA for a certain period of time the activity of the generated amount of immuno-immobilized two-chain u-PA was determined with plasminogen and the chromogenic substrate S-2251. The scu-PA activator activity (scuPA-AA) in the DEF of plasmas deficient in factor XII or prekallikrein was about half of that in the DEF of normal plasma. Separation of scuPA-AA in the DEF by gel chromatography showed to major peaks, one eluting with an apparent Mr of 500,000 and the other around Mr 100,000. The former peak, which coincided with the activity peak of the kallikrein-kininogen complex, was absent in the DEF of plasma depleted of prekallikrein and therefore was identified as kallikrein. The latter peak was still present in the depleted plasma and most likely represents plasmin, because its scuPA-AA coincided with the activity peak of plasmin and could be fully inhibited by antibodies raised against human plasminogen. It is concluded that plasmin and the contact-activation factor kallikrein each contribute for about 50% to the scuPA-AA in the DEF. Compared on a molar basis, however, plasmin was found to be almost 1,000 times more effective than kallikrein, and we conclude, therefore, that in vivo plasmin is the primary activator of scu-PA and the role of the contact system is of secondary importance.
LINK
